Products

Customer Service

+82-32-819-2900
Mon-Fri:09:00-18:00
Lunch Time:11:50-12:40

Hommage

Product Category

detail image

product description

Hommage creates elegant and dignified spaces by forming embossed surfaces and offers even marble patterns with single application. It is an eco-friendly construction material that satisfies the toxin-free standards of RoHS. It is free of VOCs, smell, and pollution and shows excellent physical properties, such as water-resistance, alkaline-resistance, and durability. With its smooth surface finish, this spray paint for natural stone finish is designed to create smooth and the most realistic appearance of natural stone.

applicaition

  • 1) General Use
    • ? Special applications on apartments (lower floors below 4, pilotis, canopies, etc)
    • ? Exterior walls and special applications on buildings and multifamily houses
    • ? Interior/exterior walls of any type of buildings, i.e., concrete, plaster board, plywood, PC board, ALC board, GRC board, retaining walls, etc
  • 2) Matte Finish Applications
    • ? Painted surfaces
    • ? Other finished surfaces

materials

ItemProductAmount
(kg/㎥)
MethodColorRemarks
UndercoatCombi Primer0.15-0.2 B, R, S Any Color Matching color for joints or lining
Under LiningHommageCombi HM Embo0.8-1.2SAny Color
LiningCombi HM Embo0.5-1.0SAny ColorPatterning/coloring Use special gun
TopcoatCombi Water-soluble AS#300 0.15-0.2B, R, SClearWater-soluble coat with improved contamination-resistance

conditions

  • 1) The weather condition should be 5℃ or higher in temperature, 85% or lower in relative humidity, and 5m/sec or lower in wind velocity with no rainfall or snowfall.
  • 2) Dry for sufficient length of time (10% or lower water content; pH 9 or lower).
  • 3) Must not have dust, grease, or impurities.
  • 4) Must not have cracks, grooves, or damages.
  • 5) Must not have pinholes or blowholes.

process chart

Joint Finish
Process Material
Mixing
(Ratio)

Amount
(kg/㎟)

No of Coats,Interval (HR) Method
Within Process Between Process Final Curing
1 Surface Preparation
/Inspection
Impurities on the surface should be completely removed.Use putty to flatten grooves, cracks, and damages.
2 Undercoat Combi Primer 100 0.15~0.2 1~2   4 or longer   Brush, Roller, Spray
Tap Water 5% or lower
3 Joint Drawing Line Design the position of joints and draw a line with ink or chalk.
Joints Apply tape joints along the design.
4 Under Lining Combi HM Embo 100 0.8~1.2 1   24 or longer   Diameter of Gun 2.5-3.5mm
Tap Water 5% or lower
5 Lining Combi Hommage 100 0.5~1.0 2~3   2 or longer 24 or longer
6 Topcoat Combi Water-soluble AS#300 100 0.15~0.2 1~2   4 or longer 24 or longer Brush, Roller, Spray
Tap Water (5~10%)

Matte Finish
Process Material
Mixing
(Ratio)

Amount
(kg/㎟)

No of Coats,Interval (HR) Method
Within Process Between Process Final Curing
1 Surface Preparation
/Inspection
Impurities on the surface should be completely removed.Use putty to flatten grooves, cracks, and damages.
2 Undercoat Combi Primer 100 0.15~0.2 1~2   4 or longer   Brush, Roller, Spray
Tap Water 5% or lower
3 Joint Drawing Line Design the position of joints and draw a line with ink or chalk.
Joints Apply tape joints along the design.
4 Lining Combi HM Embo 100 0.5~1.0 2~3   4 or longer 24 or longer Diameter of Gun 2.5-3.5mm
Tap Water 5% or lower
6 Topcoat Combi Water-soluble AS#300 100 0.15~0.2 1~2   4 or longer 24 or longer Brush, Roller, Spray
Tap Water (5~10%)

consideration

  • 1) Temperature should be at least 5℃ when working and should stay above 5℃ for at least 3 hours (6 hours in winter) after completion.
  • 2) If relative humidity is greater than 85%, stop working as frost may be formed to cause discoloration.
  • 3) If patterns are not created properly, stop working and remove defective parts. Remove the cause of defects and resume work.
  • 4) If you have to stop while applying lining, take care not to create spray joints.
  • 5) Store paints in cool, dry shades in between 5℃ and 30℃ in temperature.
  • 6) Take care as colors may be different with putty or at joints.
  • 7) Manage lot no. to prevent difference in color.

finishing

  • 1) When complete, remove curing agent and clean.
  • 2) Remove contaminated parts or damaged parts and reapply.
  • 3) After finishing, remove any dust or impurities.

certificates

Valid XHTML 1.0 Transitional  Web Design Company